|
MGT 4.6 / MTA A-Arm Mounts. The last line of defense from suspension binding. The Original TD-Racing Upgrade.
$35.00USD (set of two) Possibly discontinued due to lack of demand.
Send me an email if you would like me to return these to production, |
|
Motor Mount with M3 Screw Mount Comes with 5- stainless steel M3 screws, (one extra.) PN TD-2350 $70.00USD |
|
SHIPPING INFO ON ALL ORDERS (Unless otherwise noted) FIRST CLASS USPS Shipping from USA Domestic- $6.00 International- $10.00 |
|
TEAM LOSI |
|
Locking Hex Nut Washers
IN STOCK! I’ve seen many solutions posted in forums and in the tips sections of magazines; Double hex nuts. Blue Loctite. Nylok Nuts,,,,,,etc,, Then I saw this in a magazine and I had to respond, dremel the nut?? Gouge the rim??? Nooooooo!
I have always used these to hold my wheel nuts securely. I do not have to crank down on the nut and I have never had a wheel come loose. The washers can also be stacked for even more locking force if needed. __________________________________ (Pack of 4) 13.3mm washers, - $3.00USD (Pack of 4) 18.3mm washers, - $3.50USD
|
|
13.3mm Inner DIA fits Stock LST2 20mm wheel hexes. Pack of 4 washers
|
|
18.3mm Inner DIA fits Upgraded 23mm wheel hexes. Pack of 4 washers |
|
TEAM ASSOCIATED MGT |
|
LST2 Single Speed Conversion Hub
|
|
Motor Mount with M4 Screw Mount Comes with 5- stainless steel M4 screws, (one extra.) PN TD-2450 $70.00USD |
|
Swivel plate Only, M3 Swivel Plate Comes with 5- stainless steel M3 screws, (one extra.) PN TD-2346 $20.00USD IN STOCK |
|
Swivel plate Only, M4 Swivel Plate Comes with 5- stainless steel M4 screws, (one extra.) PN TD-2385 $20.00USD IN STOCK |
|
NEW!! Heavy Duty Belleville Washers. 3 Times the holding force as the wave washers. (Pack of 4) 12.3 X 21.8mm washers, - $4.00USD
(Pack of 4) 17.3 X 27.7mm washers, - $4.50USD |
|
12.3mm Inner DIA fits Stock LST2 20mm wheel hexes. Pack of 4 washers
|
|
17.3mm Inner DIA fits Upgraded 23mm wheel hexes. Pack of 4 washers |
|
Locking Hex Nut Washers |
|
Use singly or stack as shown to increase the load by the number of springs used. Springs stacked inverted increase the deflection of the spring by the number of springs in the stack while retaining the load of only one across the span of the stack. Springs stacked parallel and inverted increase both load and deflection. |
|
NOTICE: COLLET ADAPTERS HAVE BEEN DISCONTINUED (Most motors are now being offered with a flat on the shaft.) |
|
DELRIN SPACER IS INCLUDED! |
|
Motor Mount with M3 Screw Mount For Tekin T8 Motors Comes with 7- stainless steel M3 screws, (one extra.) PN TD-2550 $72.00USD (OUT OF STOCK) EST Restock 5/30/2012 |
|
Swivel plate Only, M3 Swivel Plate, 6 Hole Pattern for TEKIN T8 MOTORS Comes with 7- stainless steel M3 screws, (one extra.) PN TD-2347 $22.00USD (OUT OF STOCK) EST Restock 5/30/2012 |
|
ESC Mount for LST2, AFTERSHOCK AND XXL
Made of high strength black delrin plate Comes with 4 BLACK OXIDE MOUNTING SCREWS (shown) PN TD-2348 IN STOCK
$17.00USD Locate your ESC on the plate where you want it and drill Your mounting holes. Plate can be installed in front or rear for use in mounting your radio box as well. |
|
NEW!! |